Mushkin eXtreme DDR2-667


The Mushkin DDR2-667 memory arrived with the highest price in our value roundup, an excellent heat spreader design, but performed below average at the DDR2-667 and DDR2-800 settings. We raised the voltages but did not have any success in improving the timings at these settings. However, the Mushkin ran at stock voltages for the low latency DDR2-400 and DDR2-533 settings although the 3-3-3-8 timings at DDR2-533 could not be improved with additional voltage to match the 3-2-2-7 timings of other modules. Also, this is the only memory in our group that would not run 4-3-3 settings at DDR2-800. Although the performance difference is minimal, the cost of this kit indicates the memory should perform better.

Mushkin - DDR2-667 - 2x1GB
Model # 991512
CPU Ratio Memory
Speed
Best Memory Timings
(Voltage)
(4:3) 400 DDR2 3-2-2-5
1.8V
(1:1) 533 DDR2 3-3-3-8
1.8V
(4:5) 667 DDR2 3-3-3-10
2.1V
(2:3) 800 DDR2 4-4-4-12
2.0V


Patriot DDR2-667


Patriot Memory provided their Extreme Performance series memory modules that provided above average performance at voltage settings that were more than acceptable for 24/7 operation. The memory comes with stylish heat spreaders and was able to easily clock up to DDR2-900 at extended voltages and 5-5-5-15 timings, though we recommend the lower latencies at DDR2-800.

Patriot - DDR2-667 - 2x1GB
Model # PDC22G5300LLK
CPU Ratio Memory
Speed
Best Memory Timings
(Voltage)
(4:3) 400 DDR2 3-2-2-5
1.9V
(1:1) 533 DDR2 3-2-3-7
1.9V
(4:5) 667 DDR2 3-3-3-8
2.1V
(2:3) 800 DDR2 4-3-3-8
2.1V


PQI Turbo DDR2-667


The bargain of the bunch has to be the PQI Turbo kit that is currently selling for around $117 with rebate. While the timing performance of the memory was excellent we had to run at voltages higher than the group's average to meet these settings. The base voltage for this particular model is 2.0V, something to be aware of based upon our results with the other memory modules.

PQI - DDR2-667 - 2x1GB
Model # PQI25400-2GDB
CPU Ratio Memory
Speed
Best Memory Timings
(Voltage)
(4:3) 400 DDR2 3-2-2-5
2.0V
(1:1) 533 DDR2 3-2-2-7
2.0V
(4:5) 667 DDR2 3-2-3-9
2.2V
(2:3) 800 DDR2 4-3-3-9
2.2V


Wintec AMPX DDR2-667


The Wintec AMPX DDR2 Extreme series of memory was the pleasant surprise of the group as it generated excellent timings at low voltages at the lower memory speeds. It performed average at DDR2-800, although the results are more than acceptable.

Wintec AMPX - DDR2-667 - 2x1GB
Model # 3AXD2675-1G2S-R
CPU Ratio Memory
Speed
Best Memory Timings
(Voltage)
(4:3) 400 DDR2 3-2-2-5
1.8V
(1:1) 533 DDR2 3-2-2-7
1.9V
(4:5) 667 DDR2 3-3-3-8
2.15V
(2:3) 800 DDR2 4-3-3-9
2.2V


Comparing Value Memory

All of the memory in the value section was able to run on average 4-3-3-9 settings at DDR2-800 except for the Mushkin modules that were limited to 4-4-4-12 but at a low 2.0V setting. The performance delta is extremely minor and the lower voltages are welcomed, but the Mushkin memory is the most expensive in our group so we naturally expect more from it.

The ability of all our value memory to run at very low latencies at DDR2-667 and 4-3-3-9 latencies at DDR2-800 is just incredible given the average price of $148 for a 2GB kit. Not even a year ago this type of performance in the DDR2 world would have placed this "value" memory at the top of performance charts. We found the Elpida memory to offer higher overclocks at lower memory voltages overall than the Infineon based modules, making it the current leader in value performance memory in our opinion.

The two modules that stood out were the A-Data Vitesta DDR2-533 and Wintec AMPX DDR2-667. During testing, both offered a unique combination of price, performance, and stability. All of the memory reviewed is more than acceptable for a Conroe system and the performance differences are so minor that we suggest choosing a supplier based upon prior experience, warranty, or price in this case. We will be looking at additional value memory modules from other suppliers shortly along with providing performance test results with our new Core 2 Duo Memory test platform.

Value DDR2 Recommendations
Comments Locked

123 Comments

View All Comments

  • Gary Key - Wednesday, July 19, 2006 - link

    Hi,

    We used 0701. The bios versions used for each board are listed at the bottom of the features chart.

    Thanks.
  • vmsein - Wednesday, July 19, 2006 - link

    I missed that! Thank you very much again:)
  • Bochista - Wednesday, July 19, 2006 - link

    Can we see some results for 1920 x 1200 for 23 & 24 inch monitors as well as some 2560 x 1600 results for 30 inch monitors? Also, can we see the 7950 GX2 in action where all MBs would be on an equal SLI footing?
  • Gary Key - Wednesday, July 19, 2006 - link

    We will place this on our suggestion list for Roundup Two and discuss it with the Video editors this week.
  • ivoloos - Wednesday, July 19, 2006 - link

    The article says "Users need to realize that the nForce 590 SLI Intel Edition will still use the C19 SPP that is on this board."
    I remember me that a while ago I've read somewhere NVIDIA is busy with a new SPP that will replace the C19 and should arrive somewhere around Q1 next year. Someone know whether this is this correct, or will the C19 not be replaced?
  • Gary Key - Wednesday, July 19, 2006 - link

    Yes, NVIDIA is readying a new Intel Chipset that is scheduled for release in the winter. The current C19 is now at a C1 revision, the original P5N32-SLI shipped with revision A3.
  • ivoloos - Wednesday, July 19, 2006 - link

    Ah, Thanks!!
    I plan to buy me a Core 2 Dou/Extreme system about a year from now, let's say somewhere around the release of Intels Bearlake chipset. The decision will be made then, after having a clear view at the features of that chipset and the new NVIDIA chipset.
    The article, which is very good by the way, made some doubts rise about whether that what I've read was correct or not.
    I'm curious about the period when we can expect the new NVIDIA chipset to appear on the motherboards. Any news about that (Q1/2007 perhaps?), or is too early to say something about this?
  • imaheadcase - Wednesday, July 19, 2006 - link

    I want to build a value SLI motherboard with conroe.

    Maybe compare 6 value SLI motherboards with conroe and 2 gigs of value ram in the future when boards are released?

    Thanks!
  • RogueSpear - Thursday, July 20, 2006 - link

    Am I the only one who thinks that the phrase "Value SLI" is a bit like "Military Intelligence" ?
  • Gary Key - Thursday, July 20, 2006 - link

    Great statement!!! :) I guess value in the sense that the 570SLI boards will be about $50~$75 less than the 590SLI boards. However, unless you want to really overclock the FSB, even the 570SLI boards will be a value compared to the P965 boards.

Log in

Don't have an account? Sign up now