Nanoxia refers to the Deep Silence 6 as a "truly gigantic HPTX case" and it really lives up to the name. Although it can easily be mistaken for a Deep Silence 1 from a simple picture, the proportions of the Deep Silence 6 are massive. Measuring 644mm tall and 655mm deep (25.4" x 25.8"), the Deep Silence 6 is certainly not going to fit into a space designed for standard ATX cases. The truly gigantic part of the Deep Silence 6 however is the weight. At 20.8 kg (45.8 lbs) completely empty, this is one very heavy case and is most certainly not fun to move...unless you're looking for an alternative to weight lifting.

Aesthetically, the design of the Deep Silence 6 is simple yet highly refined, with clean lines and smooth surfaces. We will be reviewing the standard version but Nanoxia also offers a version with a windowed left side panel, as well as a milk-white version. Although the case's frame is made out of 1mm thick SECC steel, the top and front covers of the case are made of plastic, including the doors and the "chimney". These are standard materials for almost every modern PC case, and Nanoxia doesn't break any new ground here.

Both doors are hinged on the right side with magnets holding the doors in place. There's also a layer of sound insulating material applied on the inside of the doors. The top door hides four 5.25" drive bays, two analog fan controllers, and the reset button (and anyone with children will likely appreciate the reset button not being quite so readily accessible). The two top 140mm fans come factory installed, with wiring going to the fan controllers; there's a single 3-pin connector available for a third fan as well. Next to the fan controllers, the logo of the company is embossed on the plastic. The 5.25" drive bay covers are held in place via a plastic lock on their right side and they're easily accessible from the front of the case; all of the drive covers have dust filters installed as well.

The bottom door will most likely be opened far less often than the top door, as it only covers the two 140mm intake fans. The intake is on the side of the case and so the door only needs to be opened if the filters require cleaning. Nanoxia makes the cleaning of the filters -- or even the replacement of the fans themselves -- extremely easy as each fan and filter is attached to its own smaller plastic door. By opening the door, the user can simply pull the filter out and clean it or remove the fan altogether.

The power button can be found at the top side of the plastic front panel, encircled by a green LED. Moving a little towards the rear, the hidden port cluster can be seen, which pops out if pressed. We assume that most of the time it will be left open, as these days it seems almost every user has something connected to a front USB port, yet the option to hide it entirely is certainly welcome. The port cluster offers 3.5mm headphone and microphone jacks, two USB 2.0 ports, and four USB 3.0 ports.

The rest of the top panel is covered by the active "air chimney", which can be opened/closed via the large switch on the side. Nanoxia calls this an "active chimney" because it also acts as a switch, turning off the top panel fans when closed. The switch is very tight but the whole mechanism feels very robust and the panels close firmly, even though all the parts involved are plastic. It is possible to partially open the panels, but it does not make any real sense in our opinion.

We received the windowless version of the case, yet the left side panel has an opening with a plastic cover installed. The plastic cover may be removed, allowing for the installation of two 120mm or 140mm fans. Nanoxia has fan filters preinstalled and waiting; however, cleaning those filters isn't quite as simple as cleaning the the front panel filters, as they are secured with screws between the side panel and the fans. Each time the user wants to clean these two filters, the side panel will have to be removed, then the fans, and only then can you remove and clean the filters. Both side panels also have dense sound insulation applied.

The rear of the case is not very interesting, although it is worth noting the very large ventilation openings next to the expansion card slots and the presence of four round holes for liquid cooling hoses and cables near the top of the case. The four holes are covered with rubber grommets, but if you do not need/want to have openings there at all, you may use the supplied rubber covers to completely seal some or all of the holes.

Wrapping up our external inspection, four tall, nickel-plated feet lift the Nanoxia Deep Silence 6 about two centimeters above the surface. A long air filter comes installed at the bottom of the case as well, for the PSU intake fan and for the optional bottom intake fans. To remove this filter, the user only has to pull it off from the rear of the case, though this is usually not very convenient or even possible without moving the whole case (again, not an easy task for someone my size).

Nanoxia Deep Silence 6: Introduction and packaging Nanoxia Deep Silence 6 Interior
POST A COMMENT

26 Comments

View All Comments

  • c4v3man - Thursday, February 13, 2014 - link

    One other thing to note, on the white case at least, the difference between the white plastic and the white painted steel is noticeable... not terrible, but when it sits on your desk awhile, you'll notice it. Reply
  • codylee - Thursday, February 13, 2014 - link

    Huge. The picture with the full ATX board looking like it's a mITX board made me double-take. I'm looking forward to a review of the DS4 (a case I could actually pick up and move if need be). Reply
  • The_Assimilator - Friday, February 14, 2014 - link

    Whoever copy edited this article (or didn't) did an atrocious job. First page, "four different cooling fans series" and "where the only option as to import their products" and it only goes downhill from there.

    Get your s**t together, AnandTech.
    Reply
  • dawp - Friday, February 14, 2014 - link

    Nanoxia is a bit older than two years, I have some of their FX 1250 fans I've had for longer than you say the company's been around.

    http://www.performance-pcs.com/catalog/index.php?m...

    maybe you should say they've been making cases for 2 years.
    Reply
  • Aslan7 - Saturday, February 15, 2014 - link

    E. Fylladitakis Would you please do temperature testing with the chimney closed? I'd trade cooling performance for the quiet. I prefer computers to run as quietly as possible and thus run as few fans as possible.

    One of my computers has a power supply fan and CPU fan and that's it the 7950 GTX with a stock oc is passively cooled. The second computer which is a current build has a core i7 3770K at 4.3GHZ 4 hard disks and a graphics card there's an intake fan on the hard disks, a single fan on the CPU, the cooler had two I removed 1, a fan on the GPU, and the power supply fan. All the fans are running slow, everything is temperature controlled, so nothing to worry about.
    Reply
  • Haravikk - Monday, February 24, 2014 - link

    It's an interesting case, but the noise levels are pretty disappointing for a case of this name. I now swear by Prolimatech Ultra Sleek Vortex 14's for both CPU coolers and case-fans; 15mm thick 140mm fans that fit 120mm fan mounts, but they are very quiet for the amount of air they push. Not quite as silent as I'd like, but a fan mechanical noise can be cancelled with a layer of acoustic foam on the inside of your case, particularly the side panel on the main access side.

    But yeah, there are definitely things that could be done to make this case a lot quieter, and which you could probably do to a more typical non "Silence" case with pretty much the same effect. The only feature that really stands out to me is the disk trays with rubber spacers, but then you can get these in many other cases too, or you can get a case with tons of 5.25" bays and install your own noise cancelation there, though of course it's more expensive that way.
    Reply

Log in

Don't have an account? Sign up now