The Kingston HyperX Fury RGB SSD Review: Bright Idea, Dimmed Performanceby Billy Tallis on September 24, 2018 8:35 AM EST
No component in a gaming desktop PC is safe from the RGB LED lighting trend. SSDs with LED lighting have existed as a tiny niche for years, but now that motherboards are integrating lighting controllers, that product segment is expanding significantly. Kingston's HyperX gaming brand is introducing the Fury RGB SSD to capitalize on the seemingly unstoppable (and oddly lucrative) trend.
The original HyperX Fury SSD was released back in 2014 and used a SandForce controller combined with 20nm planar MLC NAND. This new HyperX Fury RGB SSD has almost nothing in common with that older drive on the inside, though the non-LED parts of the visual styling are quite similar. The Fury RGB uses current-generation Toshiba/SanDisk 64-layer 3D TLC NAND and Marvell's 88SS1074 controller.
The lighting on the Fury RGB is controllable through a connector next to the SATA power and data connectors. Kingston used a USB micro-B connector here, but it's not electrically compatible with USB. Instead, the adapter cable included with the drive must be used to connect to a 4-pin 12V RGB header on the motherboard or other lighting controller. This allows the color of the lighting to be adjusted as a group; individual control of the LEDs is not possible. Alternatively, if the LED cable is not connected, the drive will default to illuminating the red LEDs using the 12V supply on the SATA power connector while the rest of the device uses the 5V supply like a normal SATA SSD. The LEDs can also be powered and controlled solely through the LED cable even when the SATA power connector is not supplying any power.
The HyperX Fury uses a staggering 75 RGB LED modules internally, mounted on the same PCB as the storage-related components. The LEDs are distributed to provide thorough coverage of the backlit HyperX logo and the edge highlights. The light shines through a thin sheet of white plastic that acts as a diffuser, and the through a perforated sheet of metal that adds some texture to the lighting effect. Those two layers also block a lot of light, which is probably why the Fury RGB needs so many LEDs. The lighting forces the HyperX Fury RGB to be slightly thicker than most SATA SSDs at 9.5mm instead of 7mm.
Left: Diffuser. Right: 75 RGB LEDs
|Kingston HyperX Fury RGB SSD Comparison|
|Capacity||240 GB||480 GB||960 GB|
|Form Factor||2.5" 9.5mm SATA|
|NAND Flash||Toshiba/SanDisk BiCS3 64-layer 3D TLC|
|Sequential Read||550 MB/s|
|Sequential Write||480 MB/s|
|Write Endurance||120 TB
On the storage side of the PCB, we find typical mainstream SATA SSD components. Kingston only provides sequential I/O performance specifications which indicate SATA-saturating peak performance, but they are not saying anything about how performance scales with capacity, nor how things behave when the SLC write cache fills up. The power draw ratings seem to be based on the drive operating with the LEDs off and peak write power of 2.5 W is reasonable for a drive using modern, low-power 3D NAND. The HyperX Fury RGB is warranted for a write endurance of 0.46 DWPD over three years, equivalent to a bit less than 0.3 DWPD if it had the 5-year warranty duration that mainstream SATA drives usually come with.
The MSRPs for the Fury RGB reflect a fairly steep price premium for the RGB lighting. The Fury RGB will hit the market with pricing more typical of an entry or mid-level NVMe SSD than a SATA SSD with only a 3-year warranty. Kingston's own A1000 low-end NVMe SSD is currently selling for well below the MSRPs of the HyperX Fury RGB, so the Fury RGB is clearly only for enthusiasts who are willing to sacrifice performance and pay a premium to get the aesthetics they want from their SSD.
It's been a while since we received a SATA drive using the Marvell 88SS1074 controller; most of the SATA drives we've been seeing lately have used either Silicon Motion or Phison controllers. The turnkey solutions offered by those two vendors seem to be a lot more popular with the smaller SSD brands than Marvell's offerings. Some of the biggest brands have also been lured away from Marvell, most notably the Crucial M/MX series that switched to Silicon Motion's SM2258 after using Marvell controllers for all their previous high-end 6Gbps SATA SSDs. Western Digital still uses the 88SS1074 controller in their WD Blue SSDs, but they switched from Marvell to an in-house controller for the 3D NAND update to their WD Black SSD.
The Toshiba/SanDisk BiCS3 64-layer 3D TLC NAND flash used in the HyperX Fury RGB is a much more common sight on our SSD testbed this year, both in NVMe and SATA SSDs. Virtually all drives using Phison controllers are using Toshiba NAND, and this includes Toshiba's own TR200 SATA SSD with the DRAMless Phison S11 controller. The Plextor M8V is a more mainstream drive, pairing the same NAND with the SM2258 controller. The M8V has been scarce at retailers but its OEM counterpart (Liteon CV8) has been used by major OEMs like Dell.
It's hard to decide which drives are the best to compare the Fury RGB against, since most of our SSDs don't have LED lighting. Ignoring the lighting aspect, the drives that are most technologically similar are the Toshiba TR200 and Plextor M8V, SATA drives with the same NAND and different controllers. The Crucial MX500 and Intel 545s are mainstream SATA drives with Intel/Micron 64-layer TLC.
The price premium that the LED lighting brings to the Fury RGB brings it up to the level of some of the cheaper NVMe SSDs. Kingston's own A1000 is an entry-level NVMe SSD using the Phison E8 controlller, and it is substantially cheaper than the Fury RGB's MSRPs. Meanwhile the ADATA XPG SX8200 uses the much higher-performing combination of Micron 64L 3D TLC and the SM2262 controller and costs about the same as the Fury RGB.
For this review, two sets of power measurements are reported for the Fury RGB: the total power draw across both 5V and 12V rails with the LEDs illuminated in their default red color, and the power on just the 5V rail. These two sets of measurements come from the same test runs, so there's only one set of performance numbers. At full brightness, the red LEDs draw about 2.24 W when powered by the SATA power connecter, and this is enough to keep the drive rather warm even when it is idle. With all three color channels illuminated, LED power consumption exceeds 4W but we did not leave it connected to the multimeter long enough for the drive to reach an equilibrium temperature and power draw. (I didn't want to burn out the breadboard I was using to wire things up.)
Our SSD coverage in recent months has been heavily focused on NVMe SSDs as the more active and exciting market segment. As a result, our post-Spectre/Meltdown re-testing of drives has included relatively few SATA SSDs. Most of our small and low-end SATA drives have not yet completed the longer AnandTech Storage Bench tests, so this review has fewer results for The Destroyer and the ATSB Heavy test than we typically include.
|AnandTech 2018 Consumer SSD Testbed|
|CPU||Intel Xeon E3 1240 v5|
|Motherboard||ASRock Fatal1ty E3V5 Performance Gaming/OC|
|Memory||4x 8GB G.SKILL Ripjaws DDR4-2400 CL15|
|Graphics||AMD Radeon HD 5450, 1920x1200@60Hz|
|Software||Windows 10 x64, version 1709|
|Linux kernel version 4.14, fio version 3.6|
|Spectre/Meltdown microcode and OS patches current as of May 2018|
- Thanks to Intel for the Xeon E3 1240 v5 CPU
- Thanks to ASRock for the E3V5 Performance Gaming/OC
- Thanks to G.SKILL for the Ripjaws DDR4-2400 RAM
- Thanks to Corsair for the RM750 power supply, Carbide 200R case, and Hydro H60 CPU cooler
- Thanks to Quarch for the XLC Programmable Power Module and accessories
- Thanks to ICY DOCK for providing a custom ExpressCage MB324SP-B hot swap bay
- Thanks to StarTech for providing a RK2236BKF 22U rack cabinet.
Post Your CommentPlease log in or sign up to comment.
View All Comments
PeachNCream - Monday, September 24, 2018 - linkForm over function. All show and no go. - Those are the first things that pop into my mind after seeing the bottom drawer performance and high power consumption. We now have reached the point where there's a component that burns more electrical energy feeding pointless LEDs than it does actually fulfilling its duties as a component in a computer. Here's to enthusiasts and gamers! Good going people. You've really made the world a better place by making LEDs on everything marketable.
rrinker - Monday, September 24, 2018 - linkMost make me an old fogey, but I totally agree. I'm not sure why any gamer or enthusiast would even buy this thing, do the flashing lights actually make up for the reduced performance - considering it's supposedly 'performance' these people are after. Perhaps this may be the jump the shark moment for RGB on everything - it's now gone so far that is actually affects the performance of the peripheral the lights are supposed to be 'enhancing'.
melgross - Monday, September 24, 2018 - linkNo, lighting is very important to a segment of that market. Lit DRAM, feet, strings of LEDs and neon inside, and out. Replacing the cover with a clear plastic one(violating the FCC protocols), is very important to them.
Stupid cases such as the ones from Alienware, and others, show what these in the gaming community want. Not all of them are like that, but a big enough percentage are, and it’s a VERY big market. They get over 100,000 people to some of the ComicCons around the country.
rrinker - Monday, September 24, 2018 - linkThe difference being, this one actually reduces performance. At least with most anything else up til now, it was just added cost and some increased power consumption, but the LEDs on the RAM don;t make the actual chips hotter, or the LEDs controllers on the mobo don't make the VR modules or chipset run hotter and throttle. I could probably run a lot of LEDs and still use less power than my system was when it had a GTX480, which I replaced with a GTX970. But that's just power draw, even if my system wasn't half buried in a stand under my printer next to my desk, gaudy case lighting wouldn't cause my CPU or GPU to throttle. This thing - this is just all-around fail. I guess this does not apply to the serious performance nut - the ones who swear they can tell the difference between 1MHz differences in clock speeds to the CPU or RAM, because they probably wouldn't be running SATA SSDs anyway, but this is just beyond insane, reducing performance and increasing cost for the sake of a bunch of flashing lights. I have a bridge to sell the people that go for this, too. Oh wait, I better add lots of LED lights to it first.
melgross - Monday, September 24, 2018 - linkRAM runs hot as it is. Adding LEDs doesn’t help. Does it damage performance? I don’t know.
qlum - Tuesday, September 25, 2018 - linkDDR4 doesn't run that hot and adding leds on the edge of the memory sticks doesn't impact the temperature of the ram much. Heat from the top of the sticks is pretty easy to dissipate. Besides that this sdd uses way too much leds and blocks most of their light.
dromoxen - Tuesday, September 25, 2018 - linkThe telling point is that you can use this without the data storage functionality (and excess cables) getting in the way of its true purpose, which is to light the way to the Promised Land
TitanX - Tuesday, September 25, 2018 - linkindeed..i want not a single light on my PC except for the HDD activity and power indicator. no glass..no view panels..just an inconspicuous black box.
MrSpadge - Monday, September 24, 2018 - linkAt least the naming is adequate: it makes you hyper furious while waiting for your data and wondering about your electricity bill!
TitanX - Tuesday, September 25, 2018 - linkdude..its 2 watts...dont think that makes more than a nickel a year on the ole bill..